DJI NAZA M V2 GPS F550 ARF KIT Landing Skid Combo - 572.18 €

DJI NAZA M V2 GPS F550 ARF KIT Landing Skid Combo


















DJI Naza M V2:
Weight MC:27g
PMU:28g
GPS:27g
LED:13g Dimensions MC: 45.5 x 32.5 x 18.5mm
PMU: 39.5 x 27.5 x 10.0mm
GPS&Compass 46(diameter)x10mm
LED: 25 x 25 x 7.0mm Working Voltage Range MC:4.8V~5.5V
VU Input: 7.4V ~ 26.0 V (recommend 2S ~ 6S LiPo)
Output(V-SEN port red wire): 3A@5V (burst current:7.5A) Power Consumption MAX: 3.15W([email protected])
Normal:1.638W([email protected]) Operating Temperature -10°C ~ 50°C Assistant Software System  Windows XP sp3 / Windows 7 / Windows 8 Supported ESC output 400Hz refresh frequency Recommended Transmitter PCM or 2.4GHz with minimum 4 channels Hovering Accuracy
(GPS Mode) Vertical:±0.8m
Horizontal:±2.5m Max Yaw Angular Velocity 200°/s Max Tilt Angle 35° Ascent / Descent 6m/s,4.5m/s Built-In Functions Multiple Autopilot Control Mode
Enhanced Fail-safe
Low Voltage Protection
S-Bus Receiver Support
PPM Receiver Support
Independent PMU Module
2-axle Gimbal Support  Supported Multi-rotor Quad-rotor I4, X4
Hex-rotor I6, X6, IY6, Y6
Octo-rotor , I8 ,V8 ,X8

F550 Flame Wheel


Features:

Frame Arms adopt PA66+30GF ultrastrength material design, providing better crashworthiness.

Integrated PCB wiring
The use of high strength compound PCB frame board, makes wiring of ESCs and battery safer and easier.

Huge assembly space
Optimized frame design, which provides abundant assembly space for autopilot systems.

Attractive Frame Arms
Provide different color frame arms: red, white, black, which makes your flight more colorful.

A total solution for hobbyists
The DT7 RC system works perfectly with DJI flight control systems requiring only a single D-Bus cable, and provides two switches and a gimbal pitch control slider. Combined with a Naza-M flight control system, Flame Wheel series flight platform and an H3-2D gimbal, it creates the best total solution for hobbyists.


NAZA M V2:
All-in-one Design
DJI adheres to continuous innovation and improvement. With the new firmware, new attitude stabilization algorithm and optimized hardware structure, the Naza-M V2 provides better flight performance.
The innovative All-in-one design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer and barometer in its light and small Main Controller. It can measure flying altitude and attitude and therefore can be used for autopilot/automatic control.

Independent PMU with amazing function extension
The Naza PMU V2 has enhanced BEC functionality and provides extendable CAN BUS ports, which can support iOSD, Zenmuse H3-2D gimbal (pitch control). Support is also included for optional Bluetooth LED module to allow parameter adjustment via a mobile APP (future firmware upgrade required for this functionality)

Advanced & Improved Attitude Stabilization Algorithm
The latest fourth generation attitude stabilization algorithm not only inherits the outstanding flight stability of DJI products, but also provides excellent maneuverability even without the GPS module. It is more flexible and stable, and gives the hobbyists a wonderful flight experience. New features have been included such as GPS course automatic compensation, GPS & Compass sensor calibration, new take-off mode and so on.

Nine Types of Multi-rotors Supported
Naza-M V2 now supports nine types of multi-rotor, which meets the different needs of the enthusiasts.
Quad I, Quad X;
Hexa I, Hexa V, Hexa Y, Hexa IY;
Octo X, Octo I, Octo V; ( Naza-M V2 does not support the aircraft which has large vibration, so when you choose to use hexa-rotor or octo-rotor, please use the vibration dampening devices accordingly.

Multiple Flight Control Modes/Intelligent Switching
It offers three types of control modes: GPS Atti. Mode (with GPS module), Atti. Mode, Manual Mode. The pilot can switch between the three modes to achieve different flight characteristics. It also can adjust automatically within the flight environment and intelligently switch between GPS Atti. Mode and Atti. Mode to make sure the flight is safe and secure. In the software at the position of the manual mode you can choose manual, attitude or failsafe; it supports one key failsafe trigger.

GPS Module Available/Accurate Position Hold
The plug and play GPS module will greatly enhance the performance for Aerial Photography with accurate Position Hold, Return-To-Home and Intelligent Orientation Control functionalities. With the GPS Module, the multi-rotor will have position and altitude locked accurately even in windy conditions. Hovering accuracy is approximately 2.5m horizontal and 0.8m vertical.

New Assistant Software for Smartphone
The Naza-M now provides assistant software for iPhone4s, iPhone5, iPad3, iPad4, iPadmini, iPod5. You can do parameter adjustments at any time on your mobile devices, using only the BTU with a built-in Bluetooth module which makes it easier and convenient. It uses low power Bluetooth to minimize the power consumption of your mobile devices. It is easy to use and will automatically save your last connection records. The password mechanism ensures your safety link. Parameters can be automatically synchronized to the Cloud Server and can be restored immediately when you changed your mobile devices.

iOSD mini supported
The Naza-M now supports iOSD Mini. This will undoubtedly give you a fantastic FPV flight performance. Depending upon DJI’s accumulation of historic and reliable information integration technology, the iOSD Mini can grab the most accurate first-hand flight data information in the shortest possible time.

Intelligent Orientation Control
Usually, the forward direction of a flying multi-rotor is the same as the nose direction. By using Intelligent Orientation Control (IOC), wherever the nose points, the forward direction has nothing to do with nose direction:
In course lock flying, the forward direction is the same as a recorded nose direction.
In home lock flying, the forward direction is the same as the direction from home point to multi-rotor

Enhanced Failsafe Mode
If your transmitter supports failsafe, then you can set failsafe through port-U. Naza controller has built-in auto level failsafe function, which means when the communication between MC and the transmitter is disconnected, the outputs of all command sticks from controller will go to center position. If the GPS module is used, you can also set RTH on failsafe. If your transmitter has only 4 channels, then MC will work in Atti. Mode by default without the failsafe function.

Two Levels of Low Voltage Protections
In order to prevent your multi-rotor from crashing or other harmful consequences caused by low battery voltage, we have designed two levels of low voltage protection. You can choose not to use this, however we strongly recommend you to enable the protection. Both levels of protection have LED warning as default. The first level will blink the red light continuously; the second level will blink red light continuously and the multi-rotor will descend and land. In manual mode when low voltage protection is triggered the LED warning will be active only.

Motor Arm and Motor Dis-arm
There are four ways to start the motors:

When you want to start the multi-rotor, you need to perform any of the ways of CSC. During the flight, if the motors stop, you can immediately execute the CSC and the motors will start. This enhances the safety of the multi-rotor; no uncontrolled starting of the motors.

Motor Disarm: There are two modes of Motor Disarm: namely Intelligent Mode and Immediate Mode. For more information, please refer to the user manual or DJI Wiki.

Note: It has a brand new, smoother take-off algorithm, which is more stable and provides a brand-new experience in supporting double spring TX; every time you let go of the throttle stick it will hover.

PPM, S-BUS & Ordinary Receiver Supported
Minimum Four channel receiver supported, also PPM and Futaba S-Bus receiver supported. PPM & S-Bus receivers (the general use of the first 8 channels of S-Bus receiver) to optimize the channel connection, the A, E, T, R, U five-channel functions are set using channel X2, use only one servo cable to connect the PPM or S-Bus to X2, this makes installation quick and easy.

Independent LED Module
The Independent LED module makes the indication of the flight status and the system status to the ground much clearer. The pilot can get information more quickly and more conveniently, even at night, he/she can get real-time flight information feedback through the LED flashing frequency and colour. In addition, the module has a USB interface, which is used for parameter settings and firmware upgrade.

Built-in Gimbal Stabilization Function
The gimbal stabilization module is compatible with almost all 2-axis gimbal systems. The system will adjust the gimbal and camera according to the attitude of the aircraft after setting the parameters the first time.

Multi-rotor One-power Output Fail Protection
In most conditions, the whole multi-rotor will retain good attitude and rotate around the frame arm with no power output, due to imbalanced mechanical structure and external environment. Rotating is mainly caused by payload and external environment. When payload is heavier, rotating speed is faster. On rotating, the hexa-rotor physical structure can cause rudder to become out of control. This humanistic protection function from Naza-M V2, in Attitude or GPS Mode, keeps attitude under control even with any one power output failed and highly reduces crash risk.

Remote Gain Adjustment
The default parameter settings are preset for you to achieve a normal flight, and also supports remote parameter adjustment by using a control slider on the TX during flight in order to obtain better performance.

New Assistant Software & Firmware Online Update
The user interface of the assistant software has been comprehensively updated and brings you a new interaction experience. Instructions will automatically appear which is very convenient. In addition, on the left side of each menu section there is additional information. The logical design makes your parameter settings more simple and convenient. Like other DJI products the Naza-M V2 firmware can be upgraded free online.

English manual, !


Package Included:
NAZA M V2:
1 x DJI NAZA-M V2 Multi-rotor Flight Controller
1 x DJI NAZA-M V2 GPS Module
1 x DJI NAZA-M PMU V2 Multi-function Module
1 x DJI NAZA-M V2 LED Module

F550:
1 X Flamewheel F550 Frame Set (Assemble is required)
6 X 2212 920KV Motor (from E300 power system)
6 X 15A OPTO ESC (from E300 power system)
4 X 9443 CCW Self-Tightening Propeller (from E300 power system)
4 X 9443 CW Self-Tightening Propeller (from E300 power system)
1 X DJI F450 / F550 Plastic Landing Skids